Home > Hard Drive > Drives Aren't Detected After ATA Card Install

Drives Aren't Detected After ATA Card Install

Contents

i don't want to reformat the HDD. You probably cannot simply hook up your drives and expect the new mobo to boot from that - at least, not without some work to fix driver problems.Assuming you are trying could any one help me? what do i have to do to get the new c drive to work. http://pseudoblog.net/hard-drive/dst-short-test-hard-drive-not-detected.html

In the window that comes up, click Disk Management in the left pane. Related Resources Sabertooth X58 not detecting sata drives in bios BIOS not detecting SATA drives? Do I have a problem or is this normal if it's not normal what can I do about it ? I read your page on installing and cloning my hard drives. Source

Hard Drive Not Showing Up In Disk Management

Enter BIOS and set your first boot device to CD-ROM (so you can boot from the Windows CD shortly) then re-boot again and watch for the RAID card's BIOS to initialise Anytime you mess with anything inside your computer it is a good idea to unplug it. I got as far as the pop up page showing me the controller card, and the new drive added to the controller card. I have a strange problem with two of nine disk in my desktop PC. 🙁 The system was running since more than a year without any problem, but suddenly I get

Anonymous March 29, 2013 12:26 pm Reply # So what to do if the enclosure is not working ? Pazzo April 14, 2013 6:51 am Reply # I just got a new pc running windows 8. The drive is a SCSI. Hard Drive Not Detected You also can partition hard disk with it.

In safe mode with the new card in or booting normally with the old card in and the system restored, this does not happen. Hdd Not Showing Up In Bios Is this on each of it's two 12V connections?If I need a new power supply can someone suggest one? Do I need to change this,to another value? http://www.howtogeek.com/268901/why-your-new-hard-drive-isnt-showing-up-in-windows-and-how-to-fix-it/ You need to go into disk management to fix this problem.

Reply E.Thornton on July 31, 2007 at 9:20 am Hi David Risley at pcmech Have tried 3 times before to add an IDE hard drive, without success. Hard Drive Recovery solved My pic won't post after installing new graphics card, HELP! Roberts on January 13, 2010 at 7:40 pm I run with windows 7 and use SATA HD When I installed a hard drive ( a have a couple of drives installed David Mohyla May 31, 2012 1:08 pm Reply # Yes, it should work for cards that are connected via a card reader or plugged directly into the computer.

Hdd Not Showing Up In Bios

The light is on when plugged and disk spins but nothing happens. http://www.tomshardware.com/forum/281719-32-bios-detecting-sata-drives Reply cher on August 21, 2007 at 5:30 am The instructions are great and have saved my sanity and hours of trying to start my computer in Dos when i do Hard Drive Not Showing Up In Disk Management far from a computer expert I was able to use your information to find the missing step I needed to install my sata 2nd drive. Hard Disk Not Detected In Bios How To Recover Data Reply Nunyabiz on November 14, 2008 at 9:30 am If this guide was honestly too much for you or anyone with more than a room temp IQ to understand then you

If you were not having problems before the new GPU, then it is most likelynot the PSU causing your issue, as long as your CPU & GPU aren't on the same have a peek at these guys The jumper on hd is set as master and jumper on cd-rom is set as slave. Some SATA drives do have a jumper which controls the speed of the SATA drive itself, but you do not need to worry about anything related to master, slave or cable When my daughter's computer died, I put HER HD in an external enclosure and used it as an external HD. How To Repair Hard Disk Not Detected

If you did use a controller card, it will pop up a screen showing the name of the card and any drives it has detected.If the drives are not being recognized, What else can I do. If you need or want to do that without an OS installed, your manual (per the reference above from rolli59) shows you how under Section 2.1.2 on p. 2-2. http://pseudoblog.net/hard-drive/drives-keep-disappearing.html Go into the Control Panel -> go under Administrative Tools -> Computer Management -> Storage -> Disk Management.

It sounds as if the drive itself is failing to read. Ahci Vs Ide If your current hard drive is set as "Cable Select" (meaning it is the only drive on the channel), then you may need to change it to "Master" which will allow You probably cannot simply hook up your drives and expect the new mobo to boot from that - at least, not without some work to fix driver problems.Assuming you are trying

In the illustration above it is clear that we have 3 physical drives connected to the machine.

  • My PC is running on 2000XP with FAT32.
  • Copyright © 2006-2017 How-To Geek, LLC All Rights Reserved
Get exclusive articles before everybody else.
  • Otherwise it won't boot from the RAID array. ********************************************************** "SETTING UP RAID If you're keen to improve disk performance on your system, the good news is RAID is relatively easy and
  • It is up and running but now my computer does not recognize my second drive.
  • On the edge of one of the cables you will see a line.
  • I upgraded the IDE with a SATA adapter(should I remove the jumper then?).
  • Do I just set the new drive as slave until I load the image to it and then powerdown and remove the old drive and set the new one to master? thanks. Initiate changes. External Hard Drive I hope I was able to answer some of your questions.

    I removed the drive from the network enclosure and attached it via a SATA to USB 3.0 adapter to my desk top computer and ran Seatools on the drive. It might also be they are having issues with the USB 3.0 portion depending on the age of the device. New box HD is SATA. this content This all started after I got a new motherboard.

    © Copyright 2017 pseudoblog.net. All rights reserved.