This will not help and will make it terribly difficult to get your dual-boot working again! Flag Permalink This was helpful (0) Collapse - Just have to ask by GenRommel / December 23, 2007 4:46 AM PST In reply to: Thanks everyone............ In the "Add an Entry" section change the Drive in the dropdown menu from C: to E:. And if XP had DX10 (this machine is for gaming), I would only have XP.
Reboot into the Windows XP setup CD It's very important to make sure that this partition was created at the end of the drive, or else you might no longer be Or am I doomed to always have the dvd at the ready whenever I want to run Vista?Cheers, Nicholas. When I select vista it works great but xp gives the following error: "\system32\hal.dll. So really all i did was skip a step of Partitioning by using 2 drives.
it shows disk c and disk d. Thanks. Given the prerequisites for dual booting, you should see at least two partitions: One that contains XP and one that is empty and ready for Vista. However, you will need to use Vista's recovery tools, on the Vista installation DVD, to later repair the boot menu.
I have also been trying to install xp onto a newly formatted laptop drive and get the same error after going through the 6 boot floppies when it gets ready to Windows Vista Download Finishing Up If all has gone well (assuming you followed the directions here to a tee, there is no reason for it not to have), you should be presented with the IMPORTANT NOTE â after the initial file copy Windows XP reboots and loads up the GUI-based component of the install. https://www.cnet.com/forums/discussions/dual-boot-vista-and-xp-two-different-hard-drives-264088/ This doesn't look possible with Windows, but is there at least a way to share users & applications (without running under a domain controller)?
I can change in CMOS to which one will boot up First.I installed XP on the IDE with the Sata unplugged. I am stuck, Can you please suggest me.. It's all pretty seamless though and you shouldn't encounter any technical problems. [#PAGE-BREAK#Modify Vista's Bootloader#]Page 5 - Modify Vista's Bootloader Once Vista is installed and the system reboots When it is done, it will prompt you to restart your system.
Then, Vista Setup thanks you and performs the lengthy computer performance check. My old drive is failing on me as we speak and I need to grab new set of drives - I was thinking of going with XP once again, but reading Dual Boot Windows 7 And Xp All rights reserved. Easybcd Free Boot from the Vista DVD and on the screen where you're prompted to âInstall nowâ select âRepair your computerâ.
But when i load up vista boot pro and go to system bootloader, the install bootloader tag at bottom of page does not appear when i have selected the options you check my blog HELP Flag Permalink This was helpful (0) Collapse - Just so you know. This was also the case with our tutorial on dualbooting Ubuntu and XP where Ubuntu had been installed first. Once Vista is installed call up the browser and navigate to the EasyBCD download page - download the latest version (1.7.2 at the time of writing) install and launch the application. Easybcd Download
Any ideas why not, I am kinda left hanging. Boot your computer to the Windows Vista install DVD , click Next on the regional settings screen and then click on Repair your computer in the lower left of the window. i have a windows vista installed at my drive c: and i have an extra hardisk that i am planning to install with windows xp. this content Here, you can configure: Default operating system.
Insert the Windows Vista Install DVD and reboot the computer If you see a message about hitting a key to boot the DVD, do so. Thanks a lot August 6, 2007 k henderson A very impressive how-to guide -- I'm a techie and I wasnt aware Vista had a shrink volume option. Flag Permalink This was helpful (0) Collapse - dual drives by Eugene I / November 9, 2009 6:22 AM PST In reply to: Just so you know.
Get geeky trivia, fun facts, and much more. What you should do is to use nlite and create a custom copy of the WinXP installer disc with the SATA driver included.You can check out this article for more detail Page 1 - Intro Scenario: You want to install Vista on your PC alongside your XP installation on the same drive. Back then (XP and earlier NT-based Windows versions), a special text file called boot.ini was responsible for the make-up of the boot menu, and all of the options you configured in
A good learning experience at the least. Run it in your WinXP, it should detect Vista and fix your boot record. I would like you to see if you can asist me if possible, thanks. http://pseudoblog.net/dual-boot/dual-boot-with-vista.html In some cases, the existing drive letter could conflict with the CD-rom drive letter and that's why you can't see the partition when you boot up XP installer CD.Hope this helpsDamien
And the boot files in Windows Vista are both newer and different than the ones that came before. Restart the system and load up Windows XP and the XP disk is now the primary with the Vista partition running on the secondary D: drive If you decide that dual-booting